# Question: Can I Use 12 Gauge Wire On A 20-Amp Breaker?

## Can I mix 12 and 14-gauge wire on a 20 amp circuit?

While you can use 12-gauge on a 15-amp circuit, it’s not recommended, and you should never use a 14-gauge wire on a 20-amp circuit..

## What size wire should I use for 20 amp breaker?

12-gaugeA 20-amp circuit, protected by a 20-amp breaker or fuse, must be served by 12-gauge or 10-gauge wire.

## Should I use 12 or 14-gauge wire?

If you’re wiring a circuit on which there are both lights and outlets, or you just aren’t sure which wire gauge to use, you can’t go wrong by choosing a 12-gauge wire. It’s not quite as flexible as a 14-gauge wire, and it costs a bit more, but it’s always a safe choice on a 15- or 20-amp circuit.

## What happens when you put a 20 amp receptacle on a 15-amp circuit?

If your question is “can I connect a receptacle rated for 20 amps to a circuit designed for 15 amps?”, the answer is yes, because the receptacle can handle more current than the circuit is rated for. If you exceed 15 amps, the breaker will blow, and protect the receptacle.

## Can I put lights and outlets on the same circuit?

Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes. Check with local authorities on those limitations but yes it can be done. The groundwork for all AC circuits which are wired in what is known as parallel circuitry.

## How far can you run a 20-amp circuit?

For a temperature of 100 °F and a current of 20 A (ampacity of circuit), a length of 53 feet will cause a voltage drop of 3.6 V. So to be conservative I would say 50 feet is the max length on a 120 V, 20 A permanent branch circuit. The NEC might say otherwise, though.

## Can I put a 20 amp breaker on 12 gauge wire?

12-gauge wire is the next size larger and is allowed to carry up to 20 amps. As a result, the amp rating of a circuit breaker has the following relation to the wire size that has been chosen. A 20-amp breaker is never* allowed to run any circuit whose wires (anywhere on the circuit) are 14-gauge.

## How far can you run a 12 gauge wire?

A 12 gauge wire is typically good for 15 amp at 100 feet. For your 160 feet, they suggest a 6 gauge. Even at 5% drop, you can’t get there for less than a 10 gauge wire and be remotely good.

## Can you use 14-gauge wire on a 20 amp breaker?

You can not use 14 AWG anywhere on a circuit that has a 20A breaker. If you are putting 15 amp receptacles on a 20 amp circuit with 12 gauge wire, then you MUST use the screw terminals, not the back stab terminals. … Just use the side terminals.

## How many outlets can I put on a 15 amp breaker?

8 outletsTechnically, you can have as many outlets on a 15 amp circuit breaker as you want. However, a good rule of thumb is 1 outlet per 1.5 amps, up to 80% of the capacity of the circuit breaker. Therefore, we would suggest a maximum of 8 outlets for a 15 amp circuit.

## Do I need 20 amp outlets in kitchen?

Kitchens, by code, are required to have at least two 20 amp, 120-volt circuits to be installed on every kitchen countertop. The main reason for this is so the outlet can handle enough amps to power simple kitchen cookware such as microwave ovens, toasters, and blenders.

## How deep do you need to bury electrical wire?

In general, bury metal conduits at least 6 inches below the soil surface. You may also run them at a depth of 4 inches under a 4-inch concrete slab. Under your driveway, the conduits must be below a depth of 18 inches, and under a public road or alleyway, they must be buried below 24 inches.

## Can you bury 12 2 wire?

For a 12-in. -deep trench, you can direct-bury GFCI-protected underground feeder cable with a short length of PVC conduit at the house. At 18 inches, you can use THWN-2 conductors inside a continuous length of PVC conduit, which protects the wire all the way through the trench to the house.

## Can I use 10 gauge wire on a 20-amp breaker?

Yes, you can use 10 AWG copper conductors with a 20 ampere breaker. … There’s no problem using larger conductors, other than cost to you, and difficulties associated with working with thicker conductors.

## Can 12 gauge wire handle 30 amps?

No. 12 gauge wire is rated for a maximum of 20 amps. You need a minimum of 10AWG wire for 30 amps. … Electrical current is measured in amperage (amps), and each wire gauge has a maximum safe carrying capacity.

## How far can you run 12 gauge wire on a 20 amp circuit?

50 feetYou can run a 12 gauge wire up to 70 feet on a 15 amp circuit. That number drops to 50 feet if you run 12 gauge wire on a 20 amp circuit.

## How many outlets can I put on a 20 amp breaker?

10 receptaclesOne rule of thumb is to assign a maximum draw of 1.5 amps to each receptacle, which allows for 10 receptacles on a 20-amp circuit.

## Is it OK to use 12 gauge wire on a 15 amp circuit?

Because it’s thinner and lighter, 14-gauge wire is easier to run than 12-gauge wire. However, 12-gauge wire is acceptable on both 15- and 20-amp circuits, so some electricians use it exclusively when wiring a house.

## Can you run a 14-gauge wire off a 12 gauge wire?

It’s perfectly safe to use it. Don’t worry about confusing future workers. If they want to add something to the circuit, they will have to go turn off the circuit breaker first, and then they will see they are working with a 15 amp circuit.

## Can I replace my 15-amp breaker with a 20 amp?

The answer: It’s possible, but not advisable without an electrician evaluating the situation. You should never just upgrade from a 15-amp breaker to a 20-amp one just because the current one is tripping. Otherwise, you may burn your house down via electrical fire.

## Can you bury wire without conduit?

In most cases, you’ll probably use conduit (a hollow tube through which you run individual wires). However, if you only need a power supply (without wires to control lights from inside the house,) you can use a direct burial cable, placed in the soil without conduit.